Відео

You might consider adding a "bleeder" valve to the manifold itself for instances where you need to hold a full sheet and allow air to flow. Looks like a good setup.

I owned this same machine , bought new in 1995 or 96. Put a Byrd s helix head on it in early 200?. A company called Kitty build these for Delta. I also switched the guard out to the euro type. The jet guard was safer IMO.

Can the trimmer cut Formica edge banding as well too?

Can you please make a video with screen shots of your settings in the acorn wizard?? I have the same setup as you and cannot get the motors to turn.. please thanks 🙏

May I ask what feed rate you have set when cutting the 3/4 Maple Ply?

Why didn’t you but the FESTOOL edgebander the conturo?

can you share your acorn config settings ?? i have the exact same setup as you minus the VFD and fourth axis and cannot get the motors to turn. please thanks

What part of the country are you mowing? How many hours on the mower? How much lawn do you cut?

Is that the nighthawk dust boot? Happy with it?

I just looked at these mowers yesterday. My question to you is, how is the ride? I'm mowing bumpy rutty fields.

So it sounds like their engineering never did a test install of their product before selling it.

Hey boss… the scalping wheels vibrating… take the bolt out and put a washer or two between the wheel and mounting bracket. Put the bolt back in and use a lock nut to secure it, don’t over tighten the nut and the vibration goes away.

Dude you are the first person that actually posts a video cutting 4x8 sheets did everything lined up correctly and how how long does it take to change the tools over the whole cut ?

Ok never mind my question on the other video where you are making cabinets. I thought you had to hit the rewind before hitting the green start? Anyway I’m learning as well. I want to build a vacuum table as well. What vacuum system (pump) did you use for the vacuum table?

Are you running a vacuum hold down table?

What is the maximum temperature it supports?

Would you mind showing us this boat now that you’ve updating it? Thank you.

Where did you get the ladder… same boat… thanks!

take your VFD out of your control box --EMI

Run the vacuum outlet to the outside please. Early days but in a month the headaches from long periods of intense concentration, learning to learn again, will be gone and the journey begins. That’s been my experience anyway, for what it’s worth. It’s bloody exciting though, isn’t it?

Did you ever consider just mounting the CNC directly to the table surface instead of using the QCW rails and top ?

What dust boot are u using in the elite onefinity ?

Very cool.

Thank You Very Much For The Video, this upcoming trip will only be my 2nd trip. ( Rookie Year). I was a little nervous about finding my way from Pinnacle Creek to warrior trail 11, but Thanks to this video I'm no longer afraid of Getting lost. Take Care!

What spindle and vid did you get?

I hope that electrical panel fire didn't burn down the shop!

Great content!!!

Can’t think with that dust collector on … cute puppy

I have the same boat. What brand ladder is that? Thanks for your response

Good stuff from a smart dude.

👍

I literally just got off the phone with both mozaiks and onefinity trying to figure out if you can use the cabinet software with this machine. Any issues? How did you make it happen? Mozaiks doesnt list the onefinity as having a program for??

what is the song at 7:30? Can't find it anywhere

My two cents but won't be a good practice to have the VFD in the same cabinet together with the controller

Great video can’t wait for the head to head with the Masso I’m still trying to decide between the two and I haven’t found a user that has both so I’m really excited to see what you think

Most excellent! One question, when you speed up the video, do you use the flux capacitor?

Another great video I’m excited to see what you’re thoughts are comparing the capabilities of the Acorn to the Masso g3 hopefully you can do a comparison and give your thoughts on what you like better between the two

You're absolutely impressive and can't wait to see the finished product.

I saw the post on fb, I'd still be curious to see that beast on the onefinity, just to see if it can run it, just to see if it even can move it, lol. ya know, for science...

That's a pickup not a damn truck!!!!

Hey where did you get that swing arm for the tool setter? Pretty cool

Those speeds look pretty darn slow, what's up with that.

What about rain, snow/salt?

What about rain, snow and salt in the gullies?

Does this vent to the outside? My furnace is in my garage so if I paint or do something with smoke etc, it easily ends up in the house

Very nice.

I’m wanting to use Mozaik with a Masso controller have you had any problems with the post processor? I see they have Masso listed on their website as compatible

Hate to hear that! At least you didn’t have to return it to Masso in Australia. 😮

Was there a particular reason you chose not to do a profile cut when you wanted to cut the holes through the MDF and the table top?

I had the same edge bander, never kept a setting......scrap metal! it was so bad Laguna sent me a replacement after a long hard fight. I ended up selling it at a huge lose just to be done with it. Do yourself a favor, sell it and buy a Felder 330 or Biesse small machine. There are plenty of small machines out there that are true tools. Festool has a hand held that is better than the bandit.